McFeely's 2024 Catalog - Catalog - Page 102
Fasteners
COUNTERSINKS
Make-it-Snappy® Countersink Set
Tools
A
Part #
B
A
Tired of countersinks that slip on the drill bit after one or two holes? After tightening the
setscrew half a dozen times, the drill bit is usually so scarred up that there is no hope of any
further adjustment.
Make-it-Snappy® Countersink Sets are designed so that the countersink locks onto the hex
shank and the drill bit slides through the center. A setscrew allows adjustment of the drill bit
for different screw lengths.
The bit may be replaced with equal-sized bits of any point design or length.
The countersink set includes five adjustable countersinks from 5/64” x 3/8” countersink to
9/64” x 1/2” countersink, as listed individually below. Choose from brad or standard point
high-speed steel drill bits for replacement bits. Please note: The 9/64” x 3/8” countersink is
a special purpose tool and is not included in the set; however, a 1/8” hex wrench is included.
MS-4030
Description
Price
Dual-Flute Countersink Set − Standard Point
$33.65
Tool Accessories
Dual-flute Countersinks with Standard Point HSS Bits
MS-3005
5/64” Dia Standard Point & 3/8” Countersink
$8.95
MS-3006
3/32” Dia Standard Point & 3/8” Countersink
$8.95
MS-3007
7/64” Dia Standard Point & 3/8” Countersink
$8.95
MS-3008
1/8” Dia Standard Point & 3/8” Countersink
$8.95
MS-3009
9/64” Dia Standard Point & 1/2” Countersink
$8.95
MS-3019
9/64” Dia Standard Point & 3/8” Countersink
$9.99
MS-3012
3/16” Dia Standard Point & 3/8” Countersink
$10.26
Make-it-Snappy® Trim-Head Countersink
B
Cabinet Mfg
Hardware
Trim-head screws are great for installing trim moldings in softwoods but generally require
predrilling when used in hardwoods to avoid splitting or, worse yet, stripping of the recess.
Standard countersinks either have too large a countersink or too small a pilot bit. The result
is an oversized head hole that requires excessive filling or a pilot hole that isn’t big enough
to clear the screw threads. Our trim-head countersink drills a 1/8” clearance hole and has
a 1/4” dia. countersink that fits most trim-head screws perfectly. You will need to eyeball
the depth – on countersinks this small, the use of a stop collar prevents wood chips from
clearing, leading to heat buildup, which can prematurely dull the edge on the countersink.
Part #
MS-7010
Price
$9.62
Make-it-Snappy® 82º Countersink
C
C
When you need to countersink an existing hole, this is the tool to use. Its 5/8” dia. and 82º
angle suits modern screw design perfectly. The single flute design minimizes chatter and the
potential for oval holes. Of course, the ball detent shank works perfectly with the Make-itSnappy® quick-change chuck and other quick-connect tool holders. Made of tool steel.
Part #
D
Safety
Description
1/8”-Dia Standard Point Bit & 1/4” Countersink
MS-3099
Description
Price
Make-it-Snappy 5/8” Countersink
Make-it-Snappy® Tapered Countersink Set
$11.95
D
Perfect for tapered wood screws
This set of countersinks is designed especially for use with tapered wood screws. Drill the
propersize hole and sink the head all in one operation. For best results, adjust the drilling
depth by adjusting the length of the bit using the supplied Allen wrench. This kit includes
9/64”, 11/64” and 13/64” bits with 3/8” countersinks. All fit into the Make-it-Snappy® chuck
adapter for fast bit changes.
Part #
Description
Price
Tapered Countersink Set
$39.32
Index
Storage
MS-4430
101
Pricing is subject to change at any time due to market fluctuations.
